Dissipative Heating of a Viscoelastic Cylinder under a Load Steadily Moving over Its Surface

The Fourier method is used to find the analytical solutions to two-dimensional quasistatic problems of stationary polyharmonic vibrations and dissipative heating of a linearly viscoelastic cylinder. The influence of the cylinder thickness and the width of the loading area on the thermomechanical state of the cylinder is studied based on numerical data__________Translated from Prikladnaya Mekhanika, Vol. 41, No. 2, pp. 23–32, February 2005.     

分析薄壳塑性动力响应问题的一种数值方法

探索薄壳塑性动力响应问题的分析与数值方法,是当今力学中的重要课题之一。笔者曾给出联合应用拉普拉斯变换和最小二乘法分析梁、板、壳塑性动力响应的方法。本文分别针对承受中载的短壳和长壳问题,给出只用最小二乘法分析其塑性动力响应的方法。     

Influence of corrugation frequency and amplitude on the stress state of hollow elliptic cylinders

The influence of corrugation frequency and amplitude on the displacement and stress fields is analyzed based on an approach to solving stress problems for corrugated elliptical cylinders with certain end conditions.Translated from Prikladnaya Mekhanika, Vol. 40, No. 9, pp. 87–93, September 2004.     

周向导波在空心圆柱体中传播的数值模拟研究

在石油、化工、食品和城市供水等行业,由于腐蚀等原因而引起泄漏事故,造成巨大的经济损失和资源浪费.因此,能够预先检测到管道缺陷避免事故发生显得十分重要.基于弹性动力学理论,利用Matlab编程实现周向导波在空心圆柱体中传播的数值模拟.利用特征函数展开法计算出周向导波的频散曲线及0.6MHz和1MHz各个模态的时域波形图并据此分析激励方式同周向导波传播的关系,频率为1MHz或0.6MHz时,1和2模态在空心圆柱壳中传播的周向导波中处于主导地位:各模态的径向或周向位移幅度会受到激励入射角的影响而变化并且周向导波的位移幅度随着激励入射角的增加而增加:得到特定频率下,周向导波各模态径向、周向位移的变化关系.本文结果为进一步利用实验方法研究周向导波在空心圆柱体中传播特性和缺陷检测奠定了基础.     

Some new characteristics of the confined flow over circular cylinders at low reynolds numbers

This study summarises some new characteristics of the fluid flow over a confined circular cylinder at low Reynolds numbers. Results from both two- and three-dimensional direct numerical simulations are presented at blockage ratio between 0.1 and 0.9 and Reynolds number between 120 and 500. Floquet stability analysis of selected cases will also be presented. From the two-dimensional simulations, it is found that the fluctuating lift forces decreases with blockage ratio and becomes zero (where the flow is steady) at blockage ratio of approximately 0.7–0.8. Upon further increasing the blockage ratio to 0.9, the simulations show a dramatic increase in the fluctuating lift forces, nearly an order of magnitude greater than previously reported for an unconfined cylinder flow. It is also found that for blockage ratio of 0.5, there is a long term two-dimensional instability that becomes more prominent with increasing Reynolds number. This instability has a time scale of approximately 105 time units ($D/U_{\mathit{max}}$) at Reynolds number of 500. In addition, the transition between two- and three-dimensional flow at blockage ratios up to 0.5 is investigated. It is shown that the transition Reynolds number decreases with increasing blockage ratio. At high blockage ratio of 0.5, as we increase the Reynolds number, the transition to three-dimensional flow is shown to go from unsteady two-dimensional to steady three-dimensional before transitioning to unsteady three-dimensional flow.     

Finite deformation swelling of a temperature-sensitive hydrogel cylinder under combined extension-torsion

The swelling behavior of a temperature-sensitive poly-N-isopropylacrylamide(PNIPAM) hydrogel circular cylinder is studied subjected to combined extension-torsion and varied temperature. In this regard, a semi-analytical solution is proposed for general combined loading. A finite element(FE) analysis is conducted, subjecting a hydrogel cylinder to the combined extension-torsion and the varied temperature to evaluate the validity and accuracy of the solution. A user-defined UHYPER subroutine is developed and verified under free and constrained swelling conditions. The FE results illustrate excellent agreement with the semi-analytical solution. Due to the complexity of the problem, some compositions and applied loading factors are analyzed. It is revealed that for larger cross-linked density and larger ending temperature, the cylinder yields higher stresses and smaller radial swelling deformation. Besides, the radial and hoop stresses increase by applying larger twist and axial stretch. The hoop stresses intersect at approximately R/Rout = 0.58, where the hoop stress vanishes. Besides, the axial force has direct and inverse relationships with the axial stretch and the twist, respectively. However, the resultant torsional moment behavior is complex, and the position of the maximum point varies significantly by altering the axial stretch and the twist.     

Intrinsic square function characterizations of Hardy spaces associated with ball quasi-Banach function spaces

Let X be a ball quasi-Banach function space satisfying some mild additional assumptions and H_X({ℝ}^n) the associated Hardy-type space. In this article, we first establish the finite atomic characterization of H_X({ℝ}^n). As an application, we prove that the dual space of H_X({ℝ}^n) is the Campanato space associated with X. For any given \alpha \in (\mathrm{0},\mathrm{1}] and s\in {\mathbb{Z}}_{+}, using the atomic and the Littlewood–Paley function characterizations of H_X({ℝ}^n),we also establish its s-order intrinsic square function characterizations, respectively, in terms of the intrinsic Lusin-area function S_{\alpha ,s},the intrinsic g-function g_{\alpha ,s},and the intrinsic g_{\lambda }^{\ast }-function g_{\lambda ,\alpha ,s}^{\ast }, where λ coincides with the best known range.     

爆炸荷载作用下方形夹芯板动力学响应与优化设计数值分析

为研究方形蜂窝铝板在爆炸荷载作用下的动力学响应,基于LS-DYNA非线性有限元软件,建立了TNT炸药-前后面板-蜂窝夹芯-空气的三维有限元模型。采用ALE(任意的拉格朗日欧拉)多物质流固耦合算法分析了蜂窝铝板在冲击荷载作用下的变形机理、塑性变形、能量吸收以及结构的优化。数值模拟结果表明:随着面板厚度、核心高度的增加,蜂窝铝板在冲击荷载作用下的塑性变形明显减小,抵抗变形的能力增强;随着爆轰入射角度的增加,结构的破坏程度有所减小,入射角越大这种效果越发明显。对结构给定边长和受冲击面积以及面板厚度配合比、夹芯量纲为一的高度进行了局部的优化分析,为设计优质铝蜂窝板提供参考。